How to Remove Textured “Popcorn” Ceilings from Your Home

Textured popcorn ceilings have already gone out of style many years ago. However, a lot of older houses as well as some newer ones, still have them nowadays. While taking down a ceiling that is textured is not very difficult, it’s actually a messy work that requires special safety precautions and hard work.  


There are actually two kinds of potential hazard issues, which can turn removing a ceiling that is textured into a do-it-yourself nightmare and these are:  


This is an acoustic texture that is manufactured before the 1980s that might contain asbestos and must be tested prior to the removal process. While it does not pose a serious health risk if it’s left in place, chances are removing a ceiling that contains asbestos can potentially disturb the fibers as well as result of illness. You may want to consider researching for more information about the safe removal of asbestos as it is very important that only a professional should handle that asbestos removal process.  

Painted Ceiling  

Another potential issue, which can make removing a textured popcorn ceiling more difficult is if the paint has already been applied over the texture. As a matter of fact, it prevents that texture from water absorption that is extremely necessary in order to loosen the material. Even though a painted textured ceiling could also be removed, it often requires the application of chemical strippers in order to break down the barrier, which is the paint.  

In order to find out if either of these conditions also applies to your type of ceiling, you can try combining a few drops of your preferred liquid dishwashing soap and warm water in a small sprayer. Lightly spray a small amount of the solution in that particular area that you want to check and wait for a few minutes in order for the solution to be absorbed by the surface. If the liquid will not soak in, then chances are the ceiling has already been painted. Otherwise, if the texture comes off easily, then it wasn’t painted.  

In order to test the texture of a ceiling and check if there is any asbestos, you can use a putty knife and scrape a tiny amount of it into a sealable bag. If you are concerned regarding with the possible dangers involved in taking a sample, you can hire a professional testing service to come out as well as take it for you.  

You can then send the sample to a qualified and approved testing service in order to see if it really contains asbestos. Furthermore, in order to find the right testing service in your location, you can also contact your health office or the Environmental State office. On the other hand, you can also hire a professional popcorn ceiling removal service provider in order to make sure that the job will be done in the most efficient, effective, and timely manner. Aside from that, a professional also has the right tools and equipment needed for the popcorn removal process, which means you will rest easy knowing that the entire project will be done safely.  


Read More

3 Types of Solar Panels: Advantages and Disadvantages

Solar panel system is now becoming more popular when it comes to powering electric supplies, both in industries and homes. It doesn’t only save you big bucks of money on energy saved, but it also helps the environment in so many ways. It is a great investment since it has a long life expectancy, but you need to consider first what type of solar panel will work best for you. The following are the types of solar panels to choose from, and its advantages and disadvantages.  

 Solar Panels


Monocrystalline panels are cut from silicon in a cylindrical way. Each cell when combined makes up this type of panel. It originated in the 1950s, the first technology of solar panels. They give the highest performance rate in the panel industry because it’s made from high-quality silicone. It uses the space wisely, thus can offer a high power yield per square foot. It has a life expectancy of 25 years. It can perform best on warm weather. However, it can be too costly because they are high-quality.  


Polycrystalline is also manufactured from silicon, but unlike monocrystalline it is poured into a mold instead of cutting out. Then it will form the panels. If you’re using a solar panel for your home, this type of panel is good for you. It is cost-effective, so good news for those who are tight in budget and it also produces little waste which is good for the environment.  

Its disadvantage however is that its efficiency is lower, so don’t expect it to work well on industrial buildings. It also requires more space upon installation. If you want to produce the same power as monocrystalline, you have to look for a bigger space for this panel.  

Thin Film 

Thin film is manufactured from amorphous silicon by putting down layer upon layer of it. Thin film is lightweight, and it’s immune to damages caused by obstructions, shading or low-light conditions. These things don’t hinder the performance of the solar panel. It is also affordable because it is mass-produced. If you want to power up your home or commercial space, you can opt for this one.  

However, you have to remember that it also comes with disadvantages too. When it comes to efficiency and performance, it scores very low with the operating efficiency of 9%. A big space is also required, so if you have a tight space it won’t work. When you use it for commercial purposes, it will work. It is also costly because of the number of panels needed to manufacture it. To accommodate the system you have purchase more elements like cable and others.  

Solar panel system is complicated, so when you buy one from Solar Panel Riverside RI USA make sure you talk with the manufacturers about the power you need and how much electricity all of your appliances consume every month. You also have to consider you location, the weather, your budget of course and a couple of other things. It might cost you a lot on the first purchase but imagine your savings over the years.  

Read More

How to Properly Shape Your Shrubs 

Shaping your shrubs is like shaping your trees, though smaller and shorter. However, the techniques are similar to each other so the plant’s health and growth won’t be compromised and encouraged instead. Pruning is important to plants. Not pruning your plants, including shrubs, will reduce flowering, obscure the structure and invites fungal disease.  


If you want to prune the shrub to control its size, don’t waste your time anymore because it will just grow back. You can guide your shrubs instead so they can grow as a mature plant with healthy foliage and strong stems. Experienced gardeners and Annapolis tree services usually perform pruning during the shrub’s dormancy and perform follow-up shaping during its growing season.  

For flowering shrubs, prune them after they’ve bloomed and before they set the buds for the next flowering. Spring bloomers like azalea, rhododendron, and others should be shaped in mid-summer. Summer bloomers like glossy abelia and crape myrtle should be shaped in autumn.  

Timing is Key 

For deciduous spring-flowering shrubs, you can encourage its lush growth by trimming as soon as its blooms fade. Make you cut as cleanly as possible and leave a stub. When you prune the younger shrubs, make sure to prune branches back to healthy buds pointing in the direction you want it to grow or to nonflowering shoots. Remember to cut weak or diseases stems to remain the wood healthy. After or before using it, disinfect the blades so diseases won’t be spread.  

If you have a newly planted shrub, it will require cutting back after its first bloom. It will help the shrubs to grow with a strong framework and bloom later after the first. Other shrubs that don’t heavily bloom on their first require trimming. Make sure to cut out wayward branches and their main shoots trimmed.  

The older shrubs you have in your garden will occasionally need trimming and reshaping to look attractive. Take note on the work occasionally, it means it still needs some because an overgrown and neglected shrub will not look good.  


Whether the trees or shrubs are deciduous or evergreen, both still have a dormant period. Its dormancy is typically during the cold winter months, except for those tropical trees. During this dormant period, their active growth is suspended to it’s better to do the pruning and trimming.  

When Shaping Shrubs 

When you shape the shrub, respect their natural habitat so you can achieve optimum results. Shrubs are genetically programmed for a certain profile, size and branching pattern. That’s why it’s important that you have knowledge about the biology of trees and shrubs so you would know what cut that supports their natural features and will preserve their essential characters.  

Properly pruning shrubs, indoor houseplants or trees is important. You have to encourage the plant’s growth and its production. We may have different goals for pruning (for aesthetic reasons, health, safety, growth) it’s necessary that we do the task right so the plants are not harmed.  

Read More